Issue 
Mechanics & Industry
Volume 20, Number 1, 2019



Article Number  102  
Number of page(s)  14  
DOI  https://doi.org/10.1051/meca/2018051  
Published online  08 February 2019 
Regular Article
Fault detection of damper in railway vehicle suspension based on the crosscorrelation analysis of bogie accelerations
Department of Railway Vehicles, University Politehnica of Bucharest, 313 Splaiul Independenţei, 060042 Bucharest, Romania
^{*} email: madalinadumitriu@yahoo.com
Received:
31
August
2018
Accepted:
24
November
2018
Nowadays, the conditionbased maintenance is associated more and more with railway transport to improve the safety, availability, reliability and capacity of this transport system, and to reduce life cycle costs for the railway vehicles. The conditionbased maintenance requires that vehicle components are replaced based on their real condition, which implies the fault detection and isolation during the train's operation. The paper proposes a method to detect the failure of the damper in the primary suspension of the rail vehicle, based on the analysis of crosscorrelation of the vertical accelerations measured on the bogie frame against the two axles. The numerical simulations and experimental results show a very good correlation between the bogie accelerations when the dampers are in a normal operation condition. This thing is shown based on the values of the crosscorrelation coefficient (CCC) of the bogie accelerations. The failure in a damper can be detected by the decrease of the CCC of the bogie accelerations, a confirmed fact in the results derived from numerical simulations. The proposed method has more advantages, namely, it is a signalbased method and hence does not require a complex mathematical modelling of the vehicletrack system and knowledge of its parameters or of the external conditions; the method makes relative comparisons between measurements and hence reduces the effect of the factors that influence outputs; the method can be also extended for the secondary suspension; the method can be easily implemented on any type of bogie.
Key words: Railway vehicle / primary suspension / crosscorrelation analysis / fault detection
© AFM, EDP Sciences 2019
1 Introduction
Rail transport must always have the best solutions to match the increasingly demanding requirements of a society in a permanent evolution, where the mobility standards continue to rise. To turn the rail transport into a competitive system, the railroad operators are invariably concerned with providing the availability and punctuality of the transport services, as well as their safety. Basically, avoidance of the unplanned interruptions and the minimization of the vehicle downtime for conducting the activities specific to maintenance should be well considered.
The calendarbased maintenance activities of the rail vehicles take place regularly, and the maintenance intervals are functions of time or mileage. The selection of such intervals relies on theoretical considerations, but mostly on experience, which can lead to much shorter maintenance intervals. A solution to keep the vehicle downtime at a minimum is conditionbased maintenance. Unlike the calendarbased maintenance, where the vehicle components are replaced after certain preset intervals, the conditionbased maintenance implies the replacement based on their real condition, which requires the fault detection and isolation (FDI) occurring during the operation [1]. The technique to analyse the dynamic behaviour of a vehicle during operation is known as condition monitoring, mainly applicable to systems that deteriorate in time, and is aimed at detecting and identifying fault before it causes a failure. This is a key element of the conditionbased maintenance [2–4].
The condition monitoring gives a series of benefits to the rail operators. When defects in the operation of the vehicle components are detected in an early stage, the further deterioration in its performance is prevented and safety increased. Repairs or timely replacement of the faulty components increases the reliability and availability of the railway vehicle. Last but not least, the costs associated with vehicle maintenance can be greatly reduced by using the conditionbased instead of the calendarbased maintenance.
The reliability of the suspension system of the railway vehicles is essential, on the one hand, for meeting the ride quality and ride comfort and, on the other hand, for compliance with the conditions imposed by the traffic safety [5–8]. The suspension damage generally leads to decrease or increase of the nominal parameters' values − damping and stiffness coefficients. Any deviation from nominal characteristics of suspension influences the dynamic behaviour of the vehicle or, in extreme cases, it can jeopardize the security of passengers. Detecting component faults at their early stages prevents further deterioration in vehicle performance and enhances safety. The rapid and effective monitoring techniques are essential to increase vehicle reliability and reduce maintenance cost [9,10].
The FDI methods in the literature of review fall into two major categories: signalbased methods and modelbased methods [2,3]. Mostly, only the output signals can be measured, in which case signalbased methods can be applied. The measured signal is analysed in time and/or frequency domain to find features or signatures related to particular faults. The bandpass filters, spectral analysis, maximumentropy estimation and wavelet analysis are all applicable as the signal processing method [4]. If the relation between input signal and output signal is available, detection of abrupt faults can be possible, using the modelbased fault detection method, through the evaluation of residuals [11–13]. The modelbased FDI is mainly divided into the following methods: parameter estimation method, parity equation method and observer/Kalman filterbased method [2].
The paper shows that a method for detecting a damper fault in the primary suspension of the railway vehicle can be based on the crosscorrelation analysis of the measured vertical accelerations of bogie. In fact, the method is based on the modification of the crosscorrelation coefficient of the acceleration in the bogie frame against the axles during the failure of a damper. This situation is made clear in the results from the numerical simulations based on a bogietrack sixdegree of freedom system model, which takes into account the vibration rigid modes of a twoaxle bogie − bounce and pitch, the vertical displacement of the wheels and rails and the elasticity of the wheel–rail contact. The failure of the damper is simulated by various degrees of reduction of the damping constant of the suspension corresponding to one of the wheels, compared with the reference value. Basically, a very good correlation between the bogie accelerations calculated against the axles, corresponding to the time delay between the two axles (bogie wheelbase–velocity ratio), means no damper defect. When one of the dampers is faulty, the bogie accelerations are slightly correlated, confirmed by the decrease of CCC of the bogie accelerations. The results on the CCC of the measured accelerations on a bogie in a passenger rail vehicle during travelling on the current line are introduced and they are in agreement with the results from the numerical simulations. To increase the sensitivity and accuracy of the method, the measured accelerations are filtered within the range of the resonance frequencies of bounce and pitch in the bogie by applying a bandpass filter. In this interval, the response of the system is maximum and the most responsive to the change in damping [14].
The advantage of the suggested method firstly comes from the fact that it is a signalbased method and hence it does not require, as in the modelbased methods, a complex mathematical modelling of the system and knowledge of its parameters or of the external conditions (e.g. track input) [15–18], thus providing extra benefits of robustness against nonlinearities and parameter uncertainties. The only parameters of interest are the bogie speed and wheelbase, necessary for calculating the delay in the bogie response against the two suspensions.
In comparison to other signalbased methods that use the absolute signals directly obtained by measuring the accelerations which are depending on the operating conditions [1,9,19,20], the crosscorrelation method makes relative comparisons between measurements and hence reduces the effect of the factors that influence outputs.
Even though this method is applied here for the fault detection in the vertical primary suspension, it can be also extended for the lateral primary suspension or for the monitoring of the secondary suspension (vertical or lateral). As for the system of measuring accelerations, this is independent of the bogie configuration and parameters and, therefore, it can be easily implemented on any type of bogie.
2 Analysis of the crosscorrelation in the bogie accelerations from numerical simulations
2.1 The mechanical model of the bogie and the motion equations
Figure 1 features the mechanical model of a twoaxle bogie travelling at a constant velocity V on a straight track with vertical irregularities. The model of the bogie includes three rigid bodies modelling the bogie frame and the two axles connected between them by Kelvin–Voigttype systems that model the suspension corresponding to each axle. The elastic element of the wheelset suspension has the constant 2k_{b} and the damping elements have the constant 2c_{b} _{1} and 2c_{b} _{2}, respectively. It is assumed that when there is no damper defect, the damping constants of the suspension in the two axles are equal (2c_{b} _{1} = 2c_{b} _{2}).
The rigid vibration modes of the bogie in the vertical plane, namely, bounce (z_{b} ) and pitch (θ_{b} ), are taken into account. The bogie parameters are m_{b} – bogie mass; 2a_{b} − bogie wheelbase; − inertia moment; and i_{b} − the gyration radius of the bogie. The wheelsets of mass m_{w} have a translation motion in the vertical direction (z_{w} _{1,2}).
Neglecting the coupling effects between the wheels due to the propagation of the bending wavelength, in the frequency domain specific to the vertical vibrations of the vehicle, an equivalent model with lumped parameters will be selected. Against each axle, the track is represented as an oscillating system with one degree of freedom that has a vertical motion, with the displacement z_{r} _{1,2}. The equivalent model of the track has mass m_{r} , stiffness 2k_{r} and the damping coefficient 2c_{r} .
The elasticity of the wheel–rail contact will be chosen by introducing certain elastic elements with a linear characteristic. The calculation of the stiffness in the contact elastic elements − 2k_{H} for a wheel–rail pair − is done based on the Hertz's theory of contact between two elastic bodies by applying the linearization of the relation of contact deformation against the deformation corresponding to the static load on the wheel.
The track vertical irregularities are described against each axle via a pseudostochastic function [21]:(1)with x _{1} = Vt and x _{2} = Vt − 2a _{ b }.
The amplitude U_{k} of the spectral component‚ k′, corresponding to the wavelength Ω_{ k }, is established with the help of the power spectral density of the track vertical irregularities, as defined in ORE B176 [22]:(2)where Ω_{ c }= 0.8246 rad/m, Ω_{ r }= 0.0206 rad/m and A _{QN1,2} is a constant depending on the track quality; for the lag of the spectral component ϕ_{ k } of the spectral component‚ k, ^{′} an uniform random distribution is selected.
The constant A _{QN1,2} is calculated so that the standard deviation of the vertical alignment (σ_{η} _{QN1,2}) due to the components with the wavelength ranging from Λ_{1} = 3 m to Λ_{2} = 25 m correspond with the information in the UIC 518 Leaflet [23], subject to the track quality level, QN1 or QN2 (see Fig. 2)(3)with(4)
The coefficient K_{η} is a scaling coefficient of the amplitudes in the track vertical irregularities, a result of the ratio between the magnitude of the admitted isolated defect η _{admQN1,2} as in the UIC 518 Leaflet (see Fig. 3) and the absolute magnitude of the vertical irregularities (maxη(x _{1,2}))(5)Function f(x _{1,2}) is an adjustment function applied to the distance L _{0}, in the form of(6)where H(.) is Heaviside step function.
The vertical motions of the bogietrack system are described by six motion equations, corresponding to the vibration modes of the bogie − bounce and pitch, the vertical displacements of the wheels and of the rails.
The equations defining the bounce and pitch motions of the bogies are(7) (8)where F_{s} represents the force due to the secondary suspension of the vehicle and F_{bi} are the forces from the primary suspension of the axles i,(9)
The equations of the motions on the vertical direction of each axle are(10)where Q_{d} _{1,2} are the dynamic contact forces; the dynamic contact forces on the wheels of an axle are considered to be equal.
To calculate the dynamic forces, the hypothesis of the Hertzian linear contact between the wheel and the rail has been adopted for(11)where k _{H} is the stiffness of the wheel–rail contact.
The vertical displacements of the rails are to be found in(12)where(13)
The equations of motion for the bogietrack system become(14) (15) (16) (17)
A system of six differential equations of second order was thus obtained, in which the variables of state, displacements and velocities are introduced,(18)where p _{1} = z_{b} , p _{2} = θ_{ b }, p _{3,4} = z_{w} _{1,2}, p _{5,6} = z_{r} _{1,2}. The result will be a system of 12 differential equations of first order that can be written in a matrixlike form:(19)where q is the vector of the state variables, A is the matrix of the system and B is the vector of the nonhomogeneous terms. The system of equations (19) can be solved through a numeric integration by applying the Runge–Kutta algorithm.
Fig. 1
The mechanical model of the bogietrack system. 
2.2 The crosscorrelation function of the bogie accelerations
Considering the accelerations of the bogie as stationary and ergodic stochastic processes, the crosscorrelation function can be defined in the following form:(20)where a_{b} _{1}(t) and a_{b} _{2}(t) are the accelerations of the bogie frame against the axle 1 and the axle 2, respectively, and τ is the delay time between the two accelerations; τ represents the arguments of the crosscorrelation function of the accelerations. Further, this τ can range between −∞ and +∞.
The crosscorrelation function of the bogie frame accelerations is the measure of the similarity or interdependence between the two accelerations. In practice, this function shows to what extent the acceleration a_{b} _{1}(t) is similar to the acceleration a_{b} _{2}(t) after a certain time interval τ, when this has become a_{b} _{1}(t + τ). For the numerical simulations or the experiments, there is only a limited sequence of the two accelerations between t _{min} and t _{max}, with the duration T _{0} = t _{max} −t _{min}. In this case, the crosscorrelation function depends on the time t _{0} at which is calculated(21)
For evident reasons, the following condition has to be met:(22)where τ _{min} is the minimum value of τ, while τ _{max} is the maximum value.
The crosscorrelation function can be noticed to be dependent on the amplitude of the two accelerations. This aspect might represent a major inconvenience herein, since the track quality determines the response of the bogie. For this reason, the CCC of the two accelerations will be used:(23)where σ_{a} _{1} and σ_{a} _{2} are the standard deviations of the accelerations a_{b} _{1} and a_{b} _{2}.
The CCC can take values between −1 and 1, where the highest value means that the two accelerations are perfectly correlated, while the value zero shows the lack of correlation between these accelerations. When the CCC takes the lowest value (–1), the two accelerations show contrary tendencies. A CCC close to 1 confirms the good correlation between the two accelerations.
2.3 The results of the numerical simulations
This section features the results of the numerical simulations regarding the root mean square of accelerations (RMS accelerations) and CCC of the bogie accelerations when running at a constant speed on a track with vertical irregularities.
The parameters of the numerical model were provided for MindenDeutz bogie (see Tab. 1), while the contribution of 300 spectral components with wavelengths between 3 and 120 m was considered to synthesize the vertical irregularities in the track. The limit values of the interval of the wavelengths were thus calculated so that they are representative for the frequency interval of the bogie vertical vibrations.
The track vertical irregularities were synthesized for a 2000 m distance, for a QN2 quality track (Fig. 4). The standard deviations for the vertical alignment and the peak values of the isolated defects were chosen for the maximum velocity of 140 km/h, namely, σ_{η} _{QN2 }= 1.7 mm and η _{admQN2} = 10 mm (Figs. 2 and 3).
Figure 5a features the RMS accelerations of the bogie frame against the two axles at different velocities, including the maximum velocity of the bogie (140 km/h). The vertical vibrations of the bogie are noticed to amplify due to an increase in the velocity. For instance, a rise in the velocity from 50 to 140 km/h results into a 6fold value for the RMS acceleration above axle 1 and 10fold for the same acceleration above axle 2. Similarly, the bogie response is visibly not symmetrical above the two axles, due to the suspension damping and the geometric filtering effect from the bogie wheelbase [24]. The difference between the RMS accelerations in the bogie calculated above the two axles can reach almost 90%, as shown in Figure 5b.
Figures 6a and b show the RMS bogie acceleration above the two axles at a velocity of 137 km/h, calculated for different degrees of failure of a damper in the suspension of an axle. The failure of the damper is simulated by reducing the damping constant by 10–90%. The increase of the bogie acceleration during the failure of a damper in the suspension of an axle is thus underlined. For instance, a reduction in the damping constant by 50% in the suspension of the axle 1 leads to an increased RMS bogie acceleration by 15.2% above axle 1 and by 14.7% above axle 2. If the damping constant in the suspension of axle 2 is lowered by 50%, the RMS bogie acceleration increases by 10.6% above axle 1 and by 19.1% above axle 2.
Figure 7 shows the CCC of the bogie at the velocities of 117 and 137 km/h for three values of the time t _{0}: 6, 10 and 14 s. Three situations regarding the condition of the dampers have been taken into account: no defect damper (c_{b} _{1} = c_{b} _{2} = c_{b} ); defect damper in the suspension of axle 1 (c_{b} _{1} = 0.1 · c_{b} and c_{b} _{2} = c_{b} ); defect damper in the suspension of axle 2 (c_{b} _{2} = 0.1 · c_{b} and c_{b} _{1} = c_{b} ). The diagrams exhibit the delay time between the two accelerations, namely, τ = −0.077 s for V = 117 km/h and τ = −0.065 s for V = 137 km/h. When there is no damper defect, the maximum value of CCC is observed to be in the immediate vicinity of τ, which shows a very good correlation between the two accelerations. When one of the dampers fails, the CCC has a significant decrease at the τ time. Moreover, the maximum value of CCC is recorded at times different from τ (see Figs. 7a′ and b′).
Figure 8 shows the CCC calculated at τ = −2a_{b} /V for 6 s ≤ t _{0} ≤ 14 s, while considering different failure degrees of the dampers in the suspension of the front and the axle 2. Where there is no failed damper, the average value of CCC is 0.925, for the circulation at velocity of 117 and 137 km/h. The higher the failure degree of the damper, the lower the value of CCC, which is visible in the average values of CCC in Table 2.
As can be seen, the socalled area of failure shown in Figure 8‚ is limited by the lowest value of CCC of the accelerations calculated for the normal operation state of the dampers. If the values of CCC of the bogie accelerations against the two axles are to be found in this area, it is about a failure of one of the dampers in the suspension of the axles.
The derived results constitute favourable premises for the identification during operation of the failure of dampers in the bogie suspension, based on the CCC of the accelerations measured on the bogie frame against the two axles.
The parameters of the numerical model.
Fig. 2
Standard deviation for vertical alignment for track quality levels QN1 and QN2. 
Fig. 3
The peak value for vertical alignment for track quality levels QN1 and QN2. 
Fig. 4
The vertical track irregularities synthesis. 
Fig. 5
The RMS velocitydependent accelerations of the bogie. 
Fig. 6
The RMS acceleration for different degrees of failure in a damper: (a) in the suspension of axle 1; (b) in the suspension of axle 2. 
Fig. 7
The CCC of the bogie accelerations: (a) and (a′): at velocity of 117 km/h; (b) and (b′): at velocity of 137 km/h. 
Fig. 8
The CCC of the bogie accelerations for different failure degrees of the damper: (a) at velocity of 117 km/h; (b) at velocity of 137 km/h. 
The average values of CCC for different failure degrees of the damper.
3 Analysis of the crosscorrelation of the measured accelerations
3.1 Measurement of the bogie accelerations
This section presents the vertical accelerations measured on a Minden–Deutz bogie frame that is fitted on a passenger vehicle for long and medium traffic where the maximum velocity is 140 km/h. Two accelerometers were installed on a side of the bogie, with one accelerometer on the bogie frame against each axle (see Fig. 9).
The measurements were carried out using a measuring chain incorporating, on the one hand, the components of the measurement, acquisition and processing system for the vertical accelerations − namely, four of 4514 Brüel & Kjær piezoelectric accelerometers and the set of the NI cDAQ9174 chassis for data acquisition and the NI 9234 module for acquisition and synthesizing the data from accelerometers, and, on the other hand, the NL602Utype GPS receiver for monitoring and recording the vehicle velocity.
The measurement of the accelerations was conducted for the circulation at constant speed, on a current line, in straight track. Registrations for the accelerations at the velocities of 117 and 137 km/h for sequences of 20 s at the sampling frequency of 2048 Hz were made. For instance, Figure 10 features the accelerations recorded by the two accelerometers for a measurement sequence at speed 137 km/h. The two accelerations are similar and the maximum value is about 4 g.
Figure 11 exhibits the spectra of the accelerations measured on the bogie frame for a measuring sequence at a velocity of 137 km/h, in the 1–200 Hz frequency range. The spectra of the accelerations show more peaks between 6.2 and 150 Hz, where the frequency peak at 6.2 Hz corresponds to the resonance frequency of the bogie bounce. For this interval, several local more peaks can be seen, in an arithmetic progression. The first peak corresponds to the frequency of 13.15 Hz, while the other peaks are located at the following frequencies: 26.25, 39.45, 52.45, 65.85, 78.65, 91.9, 105.3 and 118.1 Hz. The first peak comes from the wheel eccentricity, the second from its ovality and from the third to the ninth degree from the undulatory wear of the wheel rolling surface. Another peak can be seen at 17.15 Hz, which matches the wavelength of 2.2 m of the irregularities of the rail rolling surface, meaning a longwave rail undulatory wear.
Further on, the RMS accelerations measured at velocities of 117 and 137 km/h, respectively, are introduced. To compare such results with the RMS accelerations derived from numerical simulations, the measured accelerations are bandpass filtered in the frequency interval that corresponds to the wavelengths of the track irregularities for 3–120 m and to the velocity. For instance, Figure 12 shows the spectra of the accelerations measured on a time sequence at a speed of 137 km/h, filtered in the 0.32–12.68 Hz frequency range.
Figure 13 shows the RMS accelerations for 25 measurement sequences at the constant speed of 117 km/h and the RMS accelerations derived from numerical simulations. The measured accelerations were bandpass filtered in the range frequency of 0.27–10.83 Hz. Each measurement sequence is described by a certain value of the RMS acceleration, the values are between 0.80 and 1.84 m/s^{2}, with an average value of 1.15 and 1.19 m/s^{2}. This interval also contains the value of the RMS acceleration from numerical simulations. This value is very close to the average value of the measured RMS accelerations. The difference between the RMS acceleration from numerical simulations and the average of the measured RMS accelerations does not exceed 10%.
Figure 14 features the RMS acceleration for 20 measurement sequences at the constant speed of 137 km/h and the RMS accelerations from numerical simulations. In this case, the measured accelerations were bandpass filtered in the 0.31–12.68 Hz frequency range. The RMS accelerations measured on the bogie frame vary from 1.04 to 2.40 m/s^{2} – above axle 1, with an average of 1.63 m/s^{2}, and from 1.03 to 2.49 m/s^{2} – above axle 2, with an average of 1.75 m/s^{2}. Herein, the differences between the RMS acceleration from numerical simulations and the average values are higher than 10%, namely 18% − above axle 1; 14% − above axle 2.
Fig. 9
Mounting accelerometers on the bogie frame. 
Fig. 10
Accelerations recorded on a measured sequence at speed 137 km/h: (a) on the bogie frame above axle 1; (b) on the bogie frame above axle 2. 
Fig. 11
Spectra of the acceleration measured at speed of 137 km/h: (a) on the bogie frame over axle 1; (b) on the bogie frame over axle 2. 
Fig. 12
Spectra of the acceleration measured at speed of 137 km/h, bandpass filtered in the range frequency of 0.32–12.68 Hz: (a) on the bogie frame above axle 1; (b) on the bogie frame above axle 2. 
Fig. 13
The RMS accelerations at the speed of 117 km/h: (a) on the bogie frame above axle 1; (b) on the bogie frame above axle 2. 
Fig. 14
The RMS accelerations at the speed of 137 km/h: (a) on the bogie frame above the axle 1; (b) on the bogie frame above the axle 2. 
3.2 Calculation of the crosscorrelation of the measured accelerations
In this section, the results concerning the CCC of the accelerations measured on the bogie frame against the two axles calculated by the above method for measuring sequences of 20 s are herein introduced.
Figure 15 shows the CCC of the accelerations for different measuring sequences at the velocity of 117 and 137 km/h in Figure 16. The CCC for two accelerations has the same characteristics as the ones above, irrespective of the measuring sequence. At the time moments τ = −0.06 and τ = −0.08 corresponding to the delay between the two accelerations, CCC has maximum values that are very close to 1. This fact proves that there is a good correlation between the accelerations measured on the bogie frame against the axles.
Figure 17 shows the fact that values of the CCC of the accelerations for different measuring sequences are grouped in narrow intervals for the same velocity. At the speed of 117 km/h, CCC ranges from 0.85 to 0.96, while at 137 km/h, CCC is between 0.88 and 0.96.
Fig. 15
The CCC of the accelerations measured at velocity of 117 km/h. 
Fig. 16
The CCC of the accelerations measured at 137 km/h. 
Fig. 17
The CCC of the measured accelerations at τ = − 2a_{b} /V for different measuring sequences: (a) V = 117 km/h; (b) V = 137 km/h. 
4 Analysis of the results concerning the crosscorrelation of the accelerations derived from numerical simulations and the crosscorrelation of the measured accelerations
Figure 18 features the values of the CCC of the bogie frame accelerations for more measuring sequences at velocities of 117 and 137 km/h and the values of the CCC of the accelerations derived from the numerical simulations. The latter values are noticed to be in the central area of the dispersion interval of the values CCC of the measured accelerations. Moreover, as seen in Figure 19, the mean value of the CCC for the accelerations derived from numerical simulations at velocity of 117 km/h is very close to the average of the mean values of the measured accelerations, and they are practically equal at the velocity of 137 km/h. These results prove a good concordance between the results from theoretical model and the experiments.
Figure 18 shows the “area of failure” as the area that is limited in the superior part by the lowest value of CCC for the measured accelerations. The superior limit of the failure area depends, however, on velocity. For this case, a CCC lower than 0.85 indicates a defect in the damper at the velocity of 117 km/h. At the speed of 137 km/h, the failure in the damper can be visible for a CCC lower than 0.88.
Fig. 18
Comparison between the CCC of the measured accelerations and the CCC of the accelerations from numerical simulations: (a) V = 117 km/h; (b) V = 137 km/h. 
Fig. 19
The mean value of the CCC of the measured accelerations and of the CCC of the accelerations from numerical simulations: (a) V = 117 km/h; (b) V = 137 km/h. 
5 Conclusions
The paper points out that the failure of a damper in the vertical primary suspension of the rail vehicles can be detected based on the change of the CCC of the accelerations measured on the bogie frame against the axles. The feasibility of the method is highlighted based on the results from applications of numerical simulations, where the failure of the damper is simulated by various degrees of reduction of the damping constant of the suspension corresponding to one of the wheels, compared with the reference value. The results herein show that the highest values of CCC occur when there is no damper defect, calculated at the time moment corresponding to the delay in the bogie response against the two axles. This fact shows a good correlation between the accelerations of the bogie calculated against the two axles. The CCC lowers when one of the damper fails and the higher the failure degree in the damper, the more significant reduction in the CCC.
The results concerning the CCC of the accelerations measured on a bogie in a passenger vehicle during circulation on a current line are in agreement with the results of the numerical simulations corresponding to the “no defect damper” situation. Practically, they show a good correlation between the measured accelerations. Moreover, the socalled “area of failure” is defined as the area that is limited in the superior part by the lowest value of CCC of the measured accelerations. The superior limit of the area of failure depends on velocity, yet the CCC values are very close to each other. In order not to count this fact an inconvenience for implementing the method of detecting the damper failure, based on the crosscorrelation of the bogie accelerations, a limit value of failure can be set up so as to cover the operating velocities of the vehicle.
Acknowledgment
This work was supported by a grant from the Romanian National Authority for Science Research and Innovation, UEFISCDI, project number PNIIIP22.1PED20160212, within PNCDI III.
References
 S. Kraft, C. Funfschilling, G. Puel, D. Aubry, Predictive maintenance by the identification of suspension parameters from online acceleration measurements, Proceedings of ISMA, 2010, pp. 3503–3518 [Google Scholar]
 S. Bruni, R. Goodall, T.X. Mei, H. Tsunashima, Control and monitoring for railway vehicle dynamics, Veh. Syst. Dyn. 45 (2007) 743–779 [Google Scholar]
 R.M. Goodall, C. Roberts, Concept and techniques for railway condition monitoring, Proceedings of the International Conference on Railway Condition Monitoring, 2006, pp. 90–95 [Google Scholar]
 R.W. Ngigi, C. Pîslaru, A. Ball, F. Gu, Modern techniques for condition monitoring of railway vehicle dynamics, J. Phys. Conf. Ser. 364 (2012) 012016 [Google Scholar]
 M. Dumitriu, Numerical analysis of the influence of lateral suspension parameters on the ride quality of railway vehicles, J. Theor. Appl. Mech. 54 (2016) 1231–1243 [CrossRef] [Google Scholar]
 M. Dumitriu, Influence of the suspension damping on ride comfort of passenger railway vehicles, UPB Sci. Bull. D Mech. Eng. 74 (2012) 75–90 [Google Scholar]
 M. Dumitriu, Influence of the longitudinal and lateral suspension damping on the vibration behaviour in the railway vehicles, Arch. Mech. Eng. 62 (2015) 115–140 [CrossRef] [Google Scholar]
 M. Dumitriu, A parametric study on the influence of the nonlinear characteristics of the secondary suspension upon the vertical vibrations in the railway vehicles, UPB Sci. Bull. D Mech. Eng. 80 (2018) 125–140 [Google Scholar]
 S. Alfi, S. Bionda, S. Bruni, L. Gasparetto, Condition monitoring of suspension components in railway bogies, Proceedings of the 5th IET Conference on Railway Condition Monitoring and NonDestructive Testing, 2011, pp. 1–6 [Google Scholar]
 P. Li, R. Goodall, P. Weston, C.S. Ling, C. Goodman, Estimation of railway vehicle suspension parameters for condition monitoring, Control Eng. Pract. 15 (2007) 43–55 [Google Scholar]
 M. Jesussek, K. Ellermann, Fault detection and isolation for a railway vehicle by evaluating estimation residuals, Procedia IUTAM 13 (2015) 14–23 [Google Scholar]
 M. Jesussek, K. Ellermann, Fault detection and isolation for a nonlinear railway vehicle suspension system, J. Vib. Eng. Technol. 3 (2015) 743–758 [Google Scholar]
 J.S. Sakellariou, J.S. Konstantinos, A. Petsounis, S.D. Fassois, Vibration based fault diagnosis for railway vehicle suspensions via a functional model based method: a feasibility study, J. Mech. Sci. Technol. 29 (2015) 471–484 [CrossRef] [Google Scholar]
 M. Dumitriu, Influence of damping suspension on the vibration eigenmodes of railway vehicles, Mech. J. Fiability Durability 1 (2013) 109–115 [Google Scholar]
 P.M. Frank, S.X. Ding, T. Marcu, Modelbased fault diagnosis in technical processes, Trans. Inst. Meas. Control 22 (2000) 57–101 [CrossRef] [Google Scholar]
 P. Li, R. Goodall, Modelbased condition monitoring for railway vehicle systems, Proceedings of the UKACC International Conference on Control, University of Bath, UK, September 2004 [Google Scholar]
 H. Tsunashima, Y. Hayashi, H. Mori, Y. Marumo, Condition monitoring and fault detection of railway vehicle suspension using multiplemodel approach, Proceedings of the 17th World Congress, the International Federation of Automatic Control, Seoul, Korea, July 6–11, 2008, pp. 584–589 [Google Scholar]
 H. Tsunashima, H. Mori, Condition monitoring of railway vehicle suspension using adaptive multiple model approach, Proceedings of the International Conference on Control, Automation and Systems, Gyeonggido, Korea, 2010, pp. 584–589 [Google Scholar]
 T. Oba, K. Yamada, N. Okada, K. Tanifuji, Condition monitoring for Shinkansen bogies based on vibration analysis, J. Mech. Syst. Transport. Logistics 2 (2009) 133–144 [CrossRef] [Google Scholar]
 X. Wei, L. Jia, H. Liu, A comparative study on fault detection methods of rail vehicle suspension systems based on acceleration measurements, Veh. Syst. Dyn. 51 (2013) 700–720 [CrossRef] [Google Scholar]
 M. Dumitriu, Numerical synthesis of the track alignment and applications. Part I: the synthesis method, Transp. Probl. 11 (2016) 19–28 [Google Scholar]
 C 116, Interaction between vehicles and track, RP 1, Power spectral density of track irregularities, Part 1: definitions, conventions and available data, Utrecht, 1971 [Google Scholar]
 UIC 518 Leaflet, Testing and approval of railway vehicles from the point of view of their dynamic behaviour − safety − track fatigue − running behaviour, 2009 [Google Scholar]
 M. Dumitriu, Analysis of the dynamic response in the railway vehicles to the track vertical irregularities. Part II: the numerical analysis, J. Eng. Sci. Technol. Rev. 8 (2015) 32–39 [CrossRef] [Google Scholar]
Cite this article as: M. Dumitriu, Fault detection of damper in railway vehicle suspension based on the crosscorrelation analysis of bogie accelerations, Mechanics & Industry 20, 102 (2019)
All Tables
All Figures
Fig. 1
The mechanical model of the bogietrack system. 

In the text 
Fig. 2
Standard deviation for vertical alignment for track quality levels QN1 and QN2. 

In the text 
Fig. 3
The peak value for vertical alignment for track quality levels QN1 and QN2. 

In the text 
Fig. 4
The vertical track irregularities synthesis. 

In the text 
Fig. 5
The RMS velocitydependent accelerations of the bogie. 

In the text 
Fig. 6
The RMS acceleration for different degrees of failure in a damper: (a) in the suspension of axle 1; (b) in the suspension of axle 2. 

In the text 
Fig. 7
The CCC of the bogie accelerations: (a) and (a′): at velocity of 117 km/h; (b) and (b′): at velocity of 137 km/h. 

In the text 
Fig. 8
The CCC of the bogie accelerations for different failure degrees of the damper: (a) at velocity of 117 km/h; (b) at velocity of 137 km/h. 

In the text 
Fig. 9
Mounting accelerometers on the bogie frame. 

In the text 
Fig. 10
Accelerations recorded on a measured sequence at speed 137 km/h: (a) on the bogie frame above axle 1; (b) on the bogie frame above axle 2. 

In the text 
Fig. 11
Spectra of the acceleration measured at speed of 137 km/h: (a) on the bogie frame over axle 1; (b) on the bogie frame over axle 2. 

In the text 
Fig. 12
Spectra of the acceleration measured at speed of 137 km/h, bandpass filtered in the range frequency of 0.32–12.68 Hz: (a) on the bogie frame above axle 1; (b) on the bogie frame above axle 2. 

In the text 
Fig. 13
The RMS accelerations at the speed of 117 km/h: (a) on the bogie frame above axle 1; (b) on the bogie frame above axle 2. 

In the text 
Fig. 14
The RMS accelerations at the speed of 137 km/h: (a) on the bogie frame above the axle 1; (b) on the bogie frame above the axle 2. 

In the text 
Fig. 15
The CCC of the accelerations measured at velocity of 117 km/h. 

In the text 
Fig. 16
The CCC of the accelerations measured at 137 km/h. 

In the text 
Fig. 17
The CCC of the measured accelerations at τ = − 2a_{b} /V for different measuring sequences: (a) V = 117 km/h; (b) V = 137 km/h. 

In the text 
Fig. 18
Comparison between the CCC of the measured accelerations and the CCC of the accelerations from numerical simulations: (a) V = 117 km/h; (b) V = 137 km/h. 

In the text 
Fig. 19
The mean value of the CCC of the measured accelerations and of the CCC of the accelerations from numerical simulations: (a) V = 117 km/h; (b) V = 137 km/h. 

In the text 
Current usage metrics show cumulative count of Article Views (fulltext article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.
Data correspond to usage on the plateform after 2015. The current usage metrics is available 4896 hours after online publication and is updated daily on week days.
Initial download of the metrics may take a while.